GZYF Window Weather Stripping, Window Seal Moulding Weatherstrip for Honda Civic 2006 2007 2008 2009 2010 2011, Replaces#72450-SNA-A01 72410-SNA-A01 72950-SNA-A01 72910-SNA-A01

Great Value. It fits the contours of my 2009 Accord window frames. No need for bending or modification. Lower ratings my be because of installation error. The BIGGEST challenge will be removing and reinstalling one partially hidden nut on the bottom of mirror base. You have to have a LOT of mechanical aptitude/dexterity and proper tools to do this without removing the inner door panel. See YouTube. Make sure to put a cloth in the gap below the mirror to keep the nuts from falling into the door if you don't remove the panel. Install the rear door trim back to front and forward door trim front to back. Anchor the trim loosely at one end the screw before pushing the trim down in place to insure proper positioning. Then tighten down both the front and rear screws.

Used this in a 2009 Honda civic ex sedan, I was skeptical reading some of these comments but most them are incorrect. I received the product and everything worked fine, all parts fitted perfectly and there was no issue, installation was pretty straightforward. Definitely recommend.

This was needed to replace the cracked and damaged moulding on my car. The fit seemed to work well except there were still some slight gaps between the moulding and the window.

There is no instruction included, but you can find many videos online. It's a easy job that you can do en les than 30 minutes with few tools.

Been wanting to replace these on my 2010 Honda Accord but was afraid. After watching a few online videos, it was very easy and the fit was perfect. Very happy with the outcome.

Bought these for my 2010 Accord. Front windows fit well and an easy install. My issues are with the back windows. While the install was equally easy as the front, they don't fit as well as OEM parts. There is a slight bend in the window frame that isn't easy to duplicate with these replacement parts, and caused the replacement parts to not fit well at all. There was a significant gap towards the back between the window and the new part. I complained to the manufacturer and to their credit, they sent me new ones, at no cost to me, to try to remedy the issue. Unfortunately it didn't. I installed the first new replacement from back to front to see if that made any difference, and it did, but only slightly from the first parts. Then I realized that by SLOWLY and very GRADUALLY bending the part over my thigh could I affect an approximation of the proper bend to fit the window frame. There's still a gap, but not as big as before. If you try this be very careful. It's thin metal and bends VERY easily.Also, a trick I devised for replacing the front moldings so I didn't lose the front 8mm nut holding on the mirror; if you lose it you're sunk. What I did was apply some contact cement to one end of a piece of string, then tie the other end to something so the nut wouldn't disappear into the door and be lost forever. Then I applied contact cement to the flat side of the 8mm nut, let the glue dry on both dry per manufacturer's instructions, then joined the two parts together. Then if during assembly the nut dropped off the bolt holding the mirror, the nut wasn't going down the door, and I had another shot at attaching it. Once the bolt was on, I just pulled the string off.

Fit great, looks original. I had some minor issues getting them to seat, so I slid the clips to the same spot as the old one and it went in much better. The clips slide easily so no worries.

Shipped in protective packaging and arrived undamaged. Quality is at least as good as the original window stripping (Honda OEM). Chrome covered with protective film and holes for screws lining up perfectly. Plastic clips make for an easy installation. I was reading one review suggesting to slightly bend the window stripping for the rear window. However, I would advise not to do this as it is not necessary. The window stripping will naturally bend when screws at both ends are gradually tightened. The original window stripping for the rear windows sprung back to being straight when I removed them from my car. I will follow up on this review once I can say something about durability.